Plumbing CDACall (208) 555-0123
Home › Repair
Repair

Water heater repair in Coeur d'Alene

Water heater repair in Coeur d’Alene usually starts with no hot water, water that runs lukewarm, a tank that pops or rumbles, or a bill that crept up. Those usually trace back to a part, sediment or a valve, not a dead heater. Here’s how to narrow it down.

Symptoms and likely causes

SymptomCommon cause
No hot water, electric unitFailed heating element, tripped breaker or bad thermostat
No hot water, gas unitPilot or igniter problem, thermocouple or gas supply issue
Lukewarm waterOne failed element, thermostat set low or sediment
Rumbling or poppingSediment buildup on the tank bottom
Water at the baseLoose fitting or relief valve, or a failed tank
Rusty hot waterCorrosion inside the tank

A contractor can usually narrow it down from these descriptions before booking a visit. Gas units that won’t light, or any gas smell, are a safety matter: leave the area and call 911 or the gas utility first.

Draining a tank that’s clogged with sediment

Flushing a tank once a year keeps sediment from piling up, but a tank that hasn’t been drained in years can clog at the drain valve. If water barely trickles out of the hose, sediment is usually blocking the valve. Turn the power or gas to the heater off first, and let the water cool for a few hours, since tank water can scald.

Can a bad water heater raise your bills?

Yes, in two ways. A leaking tank or a dripping relief valve sends water down the drain all day, which shows up on the water bill. And a tank with a thick layer of sediment takes longer to heat, so the burner or elements run more, which shows up on the gas or electric bill. If either bill jumps with no change in the household, check around the base of the heater and listen for rumbling or popping.

Hard water, sediment and yearly care

The city’s water comes from the Rathdrum Prairie Aquifer (City of Coeur d’Alene Water Department), and the minerals in groundwater settle to the bottom of a tank as sediment. That’s what makes the popping and rumbling, and published guides note hard water can shorten a heater’s life. Flushing the tank once a year keeps it in check. While you’re at it, lift the relief valve lever briefly to confirm it moves and reseats, and have the anode rod, the metal rod that protects the tank from rust, checked every few years.

Temperature and safety

An optimum setting is 120°F for efficiency and function (University of Florida IFAS Extension). If the water is too hot or never hot enough, the thermostat setting is the first thing to check, and a contractor will ask about it. The relief valve on a tank is a safety part and shouldn’t be capped or blocked.

When a repair is worth it

A repair makes sense when the heater is fairly young and the fault is a single part, like a thermostat, an element or a thermocouple. It makes less sense when the tank is old, has rusted or is leaking from the body, because the next failure is likely close behind. Ask the contractor to explain what failed, whether other parts look worn and roughly how old the unit is.

That conversation gives you what you need to choose between a repair and a replacement. Note the date of the repair so you can tell later whether the fix held.

What to say on the call

Describe the symptom, the fuel type, the age on the label and any recent changes, such as a power outage or a gas interruption. That helps the contractor bring the right parts.

Sources

  1. BestReviews via KTLA: how long water heaters last
  2. University of Florida IFAS Extension: energy efficient water heaters
  3. City of Coeur d'Alene Water Department

Common questions: Water heater repair in Coeur d'Alene

Why is there no hot water?

On an electric unit it's often a failed element, thermostat or tripped breaker. On a gas unit it's often a pilot, igniter or gas supply issue. A contractor can narrow it down from the description.

What does a rumbling water heater mean?

Usually sediment buildup on the tank bottom. Ask the contractor whether a flush makes sense.

Is a leaking water heater fixable?

A loose fitting or relief valve can be repaired. A leak from the tank body means replacement.

What should be done about a gas smell?

Leave the area and call 911 or the gas utility before anything else.

How do you drain a water heater that's clogged with sediment?

Turn off the power or gas, let the water cool, shut the cold supply, open a hot tap, and drain through a hose. If the flow stops, brief bursts of cold water can loosen the sediment. A stuck or broken drain valve should be left to a plumber.

Can a leaking water heater cause a high water bill?

Yes. A slow leak at the tank or a dripping relief valve can run all day and add up on the water bill. Check the floor around the heater and the end of the relief valve pipe.

Can a bad water heater raise the electric bill?

Yes. Sediment insulates the bottom of the tank and the heating elements, so the heater runs longer to reach the set temperature. A leaking hot water line or tank makes it heat more water too.

How often should the anode rod be checked?

The heater's manual gives the interval for that model. Hard water and softened water both wear a rod faster, so it's worth having it looked at during a flush every few years.

Related pages

Ready to talk to a local pro?

Describe what's going on and ask for a quote.

Call (208) 555-0123 to get a quote.
Call (208) 555-0123 to get a quote.